SPARIN 2-Pack Screen Protector Compatible with Microsoft Surface Go 3/Surface Go 4/Surface Go 2/Surface Go, Tempered Glass, High Responsive, Scratch Resistant

Wanted to be sure to protect the screen of my new Microsoft Surface Go. The Spring Screen Pro pkg comes with two very high quality screen protectors, two wet cleaning cloths, two drying cloths, six guide stickers, two micro cleaning cloths, two dust removers/absorbers, and one bubble removal card (I used a credit card). It also comes with a step by step instruction manual in English, Chinese, and pictures.I was really impressed with the quality of all of the materials. The screen protectors are 9H, clear HD, anti-scratch, premium tempered glass. This all comes in a sealed rigid protective box for easy storage and protection of the second set of materials while in storage or in transit.Considering the fact that I usually mess up my first go round with screen protectors, I'm really glad that there were twosets of everything. (and I did mess it up by forgetting to use the dust absorber/remover, which is the last step before installation. Thus...lots of bubbles, which was completely my fault) Follow the directions in the instruction manual, and you'll get a flawless installation.Great value & Highly recommended!

This screen went on fast and was actually easier than the one I put on my cell phone which cost much more. The tabs are key. First, watch the youtube video. It shows putting 2 tabs on the short side, I used 3 tabs on the long side. The protector is very very slippery and I didn't have a helper to hold it in place while I attached the hinge tabs to the screen. So what I did (BEFORE removing film) was position it by using a small piece of scotch tape in the middle of each short end, applying the tape to the protector top first. You can then ease it in in place and make fine adjustments without worrying about messing up the provided hinge tabs. Press these scotch tape pieces to the edge of the Surface Go and double check alignment. Adjust if necessary until perfect. THEN put the 3 hinges on the long side. When these hinges are folded over and attached to the protector you can take off the scotch tape pieces and proceed to cleaning. Important: make sure there is no slack in the hinge when folding over onto the protectorI have hot air heat in my house which blows around a lot of dust. I turned the thermostat down (or up if you have A/C) so the system wouldn't trigger and start blowing dust around in the middle of my installation. I also wiped down the surface I was working on, and washed and dried hands with a microfiber dish cloth. I used wet swab, then dry swab then tacky strip. I removed the film steadily and quickly trying not to stir up any air current. (don't let the sticky side touch anything after the film is off!) I closed the hinge and it immediately started adhering from the hing side across the screen until it was solidly on. Not one piece of dust or bubble, and perfect alignment! Love it!

I bought this for my new Surface Go. I was happy to see these were thick plastic protectors and not just a film. It was fairly easy to put on even though I didn't use the little stickers that came with it as a guide.I just returned home from a last minute trip out west, where I had to fly, and had taken my Surface Go with me. While on the plane I accidentally knocked it off the tray table and it landed screen down on the aisle, hitting the side of the seat as it fell. I was devastated to see cracks in the screen and a little chip off the side, especially since I had not purchased the insurance from Mircosoft. When I got home I peeled off the screen protector and was absolutely thrilled to find the screen was in perfect condition. The screen protector had multiple scratches and cracks from the fall, but it saved the screen from any damage. Since this was a two pack, I've already put on the 2nd protector.I would definitely recommend this to anyone.

Functions well. Bubble removal not needed if you follow instructions carefully. Touch sensitivity fair. Easy to apply as much as these things can be. Clarity for sure.

Bought for Surface computer, and it was easy to install, I had a bubble on the first attempt but the YouTube showed to get rid of it, and it was gone within a few minutes.

Tough to install but it worked out great. Looks clear and great, no issues.

It's a good value with 2 covers. As noted before, the instructions are for a phone but work for a tablet. Follow the instructions step by step and it installs fine. If you have a larger screen, use 3 of the tabs instead of 2; these are the "hinges" when you flip it over onto the screen for installation. As the directions say, press from the center of the protector screen outward to press out the bubbles. I only had a few around the edges. My only confusion was which side of the protector was the "sticky" side. It's the side with the little tab. Tips: use a microfiber cloth (not the one included - save that to clean your screen) to wipe off around your work area to minimize dust, wash your hands well, work carefully but quickly keep dust down, and have lots of light near your screen so you can see those specks that can become dust bubbles. Finally, I use my fingers to press out bubbles, not the little plastic card - it can scratch the screen cover, Oh yes, read the instructions a couple times... and good luck!

I've installed three of these. They're really well sized for the device. I found installation very easy with the included stickers. I managed to install them all without and dust, bubbles, misalignment, or other issues. I installed an older version onto a Surface 2 that didn't fit (the current ones being sold fit both devices.) I ended up taking it off and I disposed of it. I folded it in half to break it for disposal and I found it to be very durable. It made it almost to folded in half before it broke. An older screen I still have installed shows no chips, cracks, or scratches.