Kensington SmartFit Space Saving Dual Monitor Arm (K55513WW)

So first off - I have been searching a long time for a 'low profile stand' that would minimize my footprint on my standing desk and allow me to cross the gap on my desk against my wall.THIS stand did it and more! Easy to install - took about 15 minutes to install and mount both my monitors using the included plate and screws. I have two monitors stands and they rock!For me the 'lack' of movement in this case 5 degree swivel left to right is just barely enough - I actually require about between 7 and 10 degrees my solution was to simply turn the base of the stand ever so slightly - that required that I did NOT push the stand completely flush with the desk. It’s still extremely secure. That said, while the stand does come with an upper felt strip to cover the top of bottom of the mounts portion of the stand, out ot concern for my new walnut desk I installed felt strips (not included) on a portion of the metal to minimize the scratching.Other that the minimal angle adjustment / swivel left to right adjustment I had to made, the vertical adjustment worked just fine for me. If you are looking for a simple stand that allows you to butt up your desk super close the wall and you don't have a need to always be adjusting your monitors THIS is the stand you should get. The vertical adjustment while manual is done via the large wheel which is super easy to adjust when needed.Bottom line if you need space both against your wall and on your desktop - grab this you won't be disappointed as it just works!

Simple to install and sturdy. Saves space and allows for a wide range of adjustments that original monitor stands may not allow. The color coded leveling may be helpful for some but I found it unnecessary. The instructions appear to be jumbled in a few places as they overlap with others but it's easy enough to figure out. One thing to keep in mind is that the monitor cannot be placed just anywhere since it does not telescope. It must be clamped to the edge of a surface or through a hole. This may not be suitable for a very deep desk.The only real gripe I have is with the foam pad. It offers very little grip and the entire arm would twist while attempting to pivot the monitor. This is with the clamp tightened to a considerable amount. A rubbery material would be far better and a textured metal plate on the underside of the clamp would also help.

I was a bit skeptical when I ordered it because it only saved me 2 or 3 inches of desk depth, but the foot is so small that it gives me so much more real estate and my 2 feet deep desk feels much bigger. Also I'm 6'2" and very few monitor stands are high enough, but with this one I still have an inch or more to go higher. Now I want to buy it for my office monitor as well. I had many monitor stands in my past and this one is Zen.

The most compact + good looking stand I have found. Already bought it a second time over last few years. Two things I don’t like are:1/ adjustments on the back wheel are bit tricky and hard to control precisely. The wheel is bit flimsy too so not great if you need to change the position of the monitor often.2/the range of horizontal angles is very limited so not great for any setups where monitor is not facing straight forward

The entire post is actually metal and is very solid. It supports my 34 inch LG ultragear ultrawide monitor with no issues. I was a bit sceptical given some of the reviews but it works way better than I anticipated.

As another review points out, the VESA adapter is not actually capable of holding a 17lb monitor without drooping or rotating. It's a shame, as the product is otherwise quite nice.If you have a light monitor it would probably be just fine, but if you are near their stated weight limit you might want to look elsewhere.

Purchased this for my work from home setup, it works to hold x2 27in ViewSonic monitors, and the central stand is wide enough to mount with zip ties a dell WD19 dock to the rear (or front). Knocking off a star because the instructions were entirely interpretative with images with no explanatory text. While assembly was not overly difficult, it is designed to rely on a central cross bar to mount both monitors horizontal to each other. I was hoping to be able to mount both of my monitors such that one would be above the other relative to one side of the central stand.Post assembly I've found it to be more "wobbly" (pressure mounted via screw mechanism) than a correspondingly mounted traditional "arm" type.

I really struggled to find a monitor stand that maximized desk space and didn't push the screen too close to my eyes. This stand is the perfect solution. Great quality and super easy to install. I really like the "wheel" on the back that makes it super easy to swap monitors. Monitor now sits in perfect position.