TechOrbits Adjustable Under Desk PC Stand and Computer Wall Mount - Computer Tower Case Holder with 360-degree Swivel

This item is extremely sturdy. Made of great material. Here's some tips to make installation easier. First of all take off the width holder and pre measure the height. Then you will need a power drill. I have a desk made of that faux wood but these screws that it came with still held tight. I made the mistake of using the long screws and drew wholes through my desk...don't do that!! The short screws will get the job done.. Once you set the tower on the holder than add the top width holder and boom. Your tower is floating! It looks nice!

It definitely holds up nicely its currently holding my pc is almost slightly to big with it all the way extend but it's been holding it like a champ 🏆 it's simple to install it's haven't tryed the under the deck mount option where you can hang it but I bump my pc constantly because it's just slightly sticking in the door way and it holds it no problem never fallen or anything

Mounting swivel on top has 4 bolt holes 6" apart. It comes with mounting screws.After a few weeks, the only issue I have is that the support elbow bracket which goes across the top of the case and down the upper side of the case is held tight by friction nuts. This elbow runs in a channel which can be adjusted to any case width. The friction nut system slips a bit over time, allowing the top of the case to lean, and I am afraid if I tighten them any more they will strip out. I would redesign this top bracket to have a long bolt/wing nut running horizontally across the case that would more securely keep this bracket from slowly extending and prevent it from developing creep.

This is a nice mount, but the instructions are these tiny pictures that give you absolutely no idea how to mount the computer. My magnifying glass did not help. I finally just gave up and used common sense, but a manufacturer should not leave it up to someone's "common sense." Not everyone has that.

This was exactly what I needed. Heavy duty and works perfectly. It is handy to have an extra set of hands when installing, but could be done alone if needed. Just remember to measure the distance need to rotate so that you don't have to move it.

A perfect example of a great idea with poor execution. This product is virtually impossible to hang by one's self. Unless you have 3-4 hands. It is very heavy (which is good re:sturdiness) but holding it up while at the same time trying to drill pilot holes and subsequently screw in the necessary screws is a no-go. Now, it is possible to detach and screw in only the mounting bracket - and then *in theory* re-attach the main body of the product to said mounting bracket.........but doing so involves using one wrench to hold one of the nuts and then turn the other nut with a second wrench......each of which have to precariously fit into blind slots that are less than 1" tall. And, with only about 3-4" of "swing room" to turn said wrenches. So, the nut progresses about 1/4 turn each time. Even if you can fit a small socket wrench in there, it takes a while. And you still have to somehow hold the heavy body of the product up while using both hands to operate the tools.Also, BTW, remember that, if you plan on using the rotation feature to turn your CPU around for easy access to rear-facing ports - you will need at least a foot of empty space on both sides of the mount. (My CPU is just over 20" deep - meaning the pivot point is 10" from the front and 1" from the rear - but the monitor cables, etc. protrude an additional couple inches - thus needing a foot on either side to allow for barrier-free rotation). Not always an available option in many offices. In my situation, the rear of the CPU is easily accessible from the other side of the desk - so this was not an issue for me, and I knew that going in. But some people forget to calculate that out ahead of time.Bottom line - it is installed and does a great job of getting the CPU off my cat-hair infested floor. It is solid so I have no worries about the quality of the materials. Only problem is the design is just plain bad.

order with worries but arrived awesome CPU under desk mount, saves lots of spaces on my desk, it's made great changed to my home office

This is kind of a unique product. I got it for my Dell desktop to secure it to a This End Up solid wood desk. Installing it was pretty simple and I feel like it stable. The last thing I would want is for it to fall and drop my computer but I have no concerns. Overall, it gives me some nice access to my computer and keeps my floor clear so I can actually vacuum underneath. I'm happy with it so far!!